Original link: https://blog.fox-it.com/2020/03/19/ldapfragger-command-and-control-over-ldap-attributes/

Written by Rindert Kramer

Introduction

A while back during a penetration test of an internal network, we encountered physically segmented networks. These networks contained workstations joined to the same Active Directory domain, however only one network segment could connect to the internet. To control workstations in both segments remotely with Cobalt Strike, we built a tool that uses the shared Active Directory component to build a communication channel. For this, it uses the LDAP protocol which is commonly used to manage Active Directory, effectively routing beacon data over LDAP. This blogpost will go into detail about the development process, how the tool works and provides mitigation advice.

Scenario

A couple of months ago, we did a network penetration test at one of our clients. This client had multiple networks that were completely firewalled, so there was no direct connection possible between these network segments. Because of cost/workload efficiency reasons, the client chose to use the same Active Directory domain between those network segments. This is what it looked like from a high-level overview.

We had physical access on workstations in both segment A and segment B. In this example, workstations in segment A were able to reach the internet, while workstations in segment B could not. While we did have physical access on workstation in both network segments, we wanted to control workstations in network segment B from the internet.

Active Directory as a shared component

Both network segments were able to connect to domain controllers in the same domain and could interact with objects, authenticate users, query information and more. In Active Directory, user accounts are objects to which extra information can be added. This information is stored in attributes. By default, user accounts have write permissions on some of these attributes. For example, users can update personal information such as telephone numbers or office locations for their own account. No special privileges are needed for this, since this information is writable for the identity SELF, which is the account itself. This is configured in the Active Directory schema, as can be seen in the screenshot below.

Personal information, such as a telephone number or street address, is by default readable for every authenticated user in the forest. Below is a screenshot that displays the permissions for public information for the Authenticated Users identity.

The permissions set in the screenshot above provide access to the attributes defined in the Personal-Information property set. This property set contains 40+ attributes that users can read from and write to. The complete list of attributes can be found in the following article: https://docs.microsoft.com/en-us/windows/win32/adschema/r-personal-information
By default, every user that has successfully been authenticated within the same forest is an ‘authenticated user’. This means we can use Active Directory as a temporary data store and exchange data between the two isolated networks by writing the data to these attributes and then reading the data from the other segment.
If we have access to a user account, we can use that user account in both network segments simultaneously to exchange data over Active Directory. This will work, regardless of the security settings of the workstation, since the account will communicate directly to the domain controller instead of the workstation.

To route data over LDAP we need to get code execution privileges first on workstations in both segments. To achieve this, however, is up to the reader and beyond the scope of this blogpost.
To route data over LDAP, we would write data into one of the attributes and read the data from the other network segment.
In a typical scenario where we want to execute ipconfigon a workstation in network Segment B from a workstation in network Segment A, we would write the ipconfig command into an attribute, read the ipconfig command from network segment B, execute the command and write the results back into the attribute.

This process is visualized in the following overview:

A sample script to utilize this can be found on our GitHub page: https://github.com/fox-it/LDAPFragger/blob/master/LDAPChannel.ps1

While this works in practice to communicate between segmented networks over Active Directory, this solution is not ideal. For example, this channel depends on the replication of data between domain controllers. If you write a message to domain controller A, but read the message from domain controller B, you might have to wait for the domain controllers to replicate in order to get the data. In addition, in the example above we used to info-attribute to exchange data over Active Directory. This attribute can hold up to 1024 bytes of information. But what if the payload exceeds that size? More issues like these made this solution not an ideal one.

Lastly, people already built some proof of concepts doing the exact same thing. Harmj0y wrote an excellent blogpost about this technique: https://www.harmj0y.net/blog/powershell/command-and-control-using-active-directory/

That is why we decided to build an advanced LDAP communication channel that fixes these issues.

Building an advanced LDAP channel

In the example above, the info-attribute is used. This is not an ideal solution, because what if the attribute already contains data or if the data ends up in a GUI somewhere?

To find other attributes, all attributes from the Active Directory schema are queried and:

• Checked if the attribute contains data;
• If the user has write permissions on it;
• If the contents can be cleared.

If this all checks out, the name and the maximum length of the attribute is stored in an array for later usage.

Visually, the process flow would look like this:

As for (payload) data not ending up somewhere in a GUI such as an address book, we did not find a reliable way to detect whether an attribute ends up in a GUI or not, so attributes such as telephoneNumber are added to an in-code blacklist. For now, the attribute with the highest maximum length is selected from the array with suitable attributes, for speed and efficiency purposes. We refer to this attribute as the ‘data-attribute’ for the rest of this blogpost.

Sharing the attribute name
Now that we selected the data-attribute, we need to find a way to share the name of this attribute from the sending network segment to the receiving side. As we want the LDAP channel to be as stealthy as possible, we did not want to share the name of the chosen attribute directly.

In order to overcome this hurdle we decided to use hashing. As mentioned, all attributes were queried in order to select a suitable attribute to exchange data over LDAP. These attributes are stored in a hashtable, together with the CRC representation of the attribute name. If this is done in both network segments, we can share the hash instead of the attribute name, since the hash will resolve to the actual name of the attribute, regardless where the tool is used in the domain.

Avoiding replication issues
Chances are that the transfer rate of the LDAP channel is higher than the replication occurrence between domain controllers. The easy fix for this is to communicate to the same domain controller.
That means that one of the clients has to select a domain controller and communicate the name of the domain controller to the other client over LDAP.

The way this is done is the same as with sharing the name of the data-attribute. When the tool is started, all domain controllers are queried and stored in a hashtable, together with the CRC representation of the fully qualified domain name (FQDN) of the domain controller. The hash of the domain controller that has been selected is shared with the other client and resolved to the actual FQDN of the domain controller.

Initially sharing data
We now have an attribute to exchange data, we can share the name of the attribute in an obfuscated way and we can avoid replication issues by communicating to the same domain controller. All this information needs to be shared before communication can take place.
Obviously, we cannot share this information if the attribute to exchange data with has not been communicated yet (sort of a chicken-egg problem).

The solution for this is to make use of some old attributes that can act as a placeholder. For the tool, we chose to make use of one the following attributes:

• primaryInternationalISDNNumber;
• otherFacsimileTelephoneNumber;
• primaryTelexNumber.

These attributes are part of the Personal-Information property set, and have been part of that since Windows 2000 Server. One of these attributes is selected at random to store the initial data.
We figured that the chance that people will actually use these attributes are low, but time will tell if that is really the case

[注意]传递专业知识、拓宽行业人脉——看雪讲师团队等你加入！